Faber Chimney Service Center in India

Verified Types

Faber Chimney Types We Service

We handle service and repair for all verified Faber kitchen chimney configurations found in Indian homes.

Auto Clean Chimney

Thermal heat element melts grease into oil collector tray.

6-Way Auto Clean Chimney

Multi-angle auto-clean coverage for heavy grease kitchens.

Fully Automatic Chimney

Smart sensor auto-start and electronic suction control.

BLDC Motor Chimney

Brushless inverter motor with high suction and low noise.

Filterless Chimney

Direct suction chamber design without mesh or baffle filters.

Baffle Filter Chimney

Stainless steel curved panels separating oil from smoke.

Wall Mounted Chimney

Standard kitchen wall hood installation with duct pipe.

Island / Ceiling Mounted

Ceiling suspended chimneys for modular open kitchen islands.

Straightline / Ductless

Compact under-cabinet or carbon charcoal recirculating units.

3D Technology Chimney

Tri-directional suction vents capturing smoke from top and sides.

Size Guide

Faber Chimney Sizes

We service all standard Faber chimney dimensions fitted in Indian kitchens.

60 cm Chimney

Suitable for 2 to 4 burner gas stoves and compact modular kitchens. We check suction balance, duct routing, and motor vibration.

Full service & cleaning available

75 cm Chimney

Suitable for 3 to 4 burner hobs with wider cooking coverage. We service BLDC motors, gesture sensors, and touch PCBs.

Filterless & auto-clean check

90 cm Chimney

Suitable for 4 to 5 burner cooktops and heavy frying kitchens. We handle high suction blower cleaning, motor winding check, and duct alignment.

Heavy suction servicing

Models & Servicing

Faber Models & Types We Service

Service details for popular Faber chimney models currently found in Indian homes. Part availability is checked according to the exact model.

Model / Type	Appliance Type	Common Problems	Service Available	Parts That May Need Replacement
Faber Sunny	Filterless Auto Clean	Oil drip from chamber, gesture sensor lag	Deep degreasing, sensor cleaning	Touch panel, capacitor, oil collector
Faber Alpha	Heat Auto Clean	Auto clean heater cold, motor humming	Heating pad check, capacitor testing	Heating pad, control switch, blower
Faber Zest DLX	Baffle Filter Wall Mount	Heavy oil choking, suction reduction	Filter degreasing, motor alignment	Baffle filters, oil cup, push switch
Faber Bonito 3D	3D Suction Technology	Side vent smoke escape, vibration	3D airflow check, blower balancing	Chimney motor, blower wheel, duct pipe
Faber Cygnus 3D	Curved Glass 3D	LED light off, speed level not shifting	Wiring continuity test, PCB service	LED light module, transformer, PCB
Faber Stella 3D	Wall Mounted 3D	Rattling sound, touch button stuck	Mount tightening, touch sensor fix	Touch sensor board, motor bearings
Faber Bliss	Filterless Touch Control	Low pull on high flame, touch freeze	Airflow testing, PCB reset	Touch panel, capacitor, power cable
Faber Iris	Curved Glass Auto Clean	Auto-clean not activating, smoke leak	Heater circuit repair, duct check	Heating element, LED lamp, duct flap
Faber Energy BLDC	BLDC Inverter Chimney	Inverter PCB error, RPM drop	BLDC drive circuit test, motor check	BLDC PCB board, inverter motor
Faber Crest Pro	Gesture & Touch Control	Hand wave gesture sensor failure	Optical sensor cleaning, recalibration	Gesture sensor module, touch glass
Faber Dazzle	Heat Auto Clean	Oil collector overflowing, heater cold	Heating element resistance test	Heating coil, oil collector tray
Faber Magnus	High Suction Heavy Duty	Motor noise at max speed, duct backdraft	Bearing lubrication, exhaust vent clear	Motor bearings, blower fan, duct pipe
Faber Comet	Straightline Under Cabinet	Push button switch stuck, weak pull	Switch panel repair, cassette cleaning	Push button switch, carbon filter
Faber Aries	Pyramid Wall Mount	Vibration on wall, motor run failure	Bracket tightening, capacitor change	Chimney motor, run capacitor, filters
Faber Hood Maple BLDC	BLDC Filterless Heat Clean	Smart speed toggle fail, RPM stutter	Inverter diagnostic, wiring check	BLDC drive, control panel, blower
Faber Hood Libra BLDC	BLDC Smart Sensor Chimney	Sensor not reading smoke level	Sensor circuit testing, reset	Sensor unit, main power PCB

Note: We service all current and older Faber chimney models. Exact part availability is verified according to the specific model after technician inspection.

Troubleshooting

Common Faber Chimney Problems We Fix

Technician checks the chimney first, identifies the real cause and explains the repair before starting.

Chimney Not Starting

Burnt fuse on PCB, loose power socket, or faulty main switch board.

Low Suction Power

Grease choked filters, bent duct pipe, or blower fan speed drop.

More Noise Than Usual

Dry motor bearings, grease load on blower, or unaligned fan wheel.

Motor Problem

Winding overheating, humming sound without spinning, or burnt coil.

Auto-Clean Not Working

Heating coil failure, auto-clean switch relay fault, or timer issue.

Touch Control Problem

Touch glass grease deposit, capacitive sensor fault, or display lag.

Gesture Control Problem

Wave sensor eye blinded by oil dirt or optical sensor PCB malfunction.

Light Not Working

Burnt LED spotlight bulb, loose internal wiring, or failed driver.

PCB Circuit Problem

Voltage fluctuation damage, burnt relay, or microchip processor error.

Oil Collection Problem

Oil dripping from sides instead of draining into the oil collector cup.

Baffle Filter Problem

Clogged stainless steel baffles, bent frame, or stuck latch pins.

Duct Pipe Problem

Torn flexible aluminum duct, bird obstruction at outlet, or sharp bends.

Vibration Problem

Loose wall mounting brackets, uneven chimney body, or unbalanced fan.

Chimney Switch Problem

Mechanical push buttons jammed with oil grease or contact carbon build-up.

Component Inspection

Faber Chimney Parts We Check

We check each component carefully. Part availability is checked according to the exact model.

Chimney Motor BLDC Motor Control PCB Capacitor Touch Panel Gesture Sensor Control Switch LED Light Transformer Auto-Clean Heating Element Oil Collector Tray Baffle Filter Blower Fan Wheel Duct Pipe Chimney Canopy Glass Remote Control Power Cable

Replacement Guide

Faber Chimney Parts Replacement

Parts are replaced only after technician inspection confirms a fault. We do not diagnose without inspection.

Part Name	When Replacement May Be Needed
Chimney Motor	If the motor has burnt winding, seized internal bearings, or fails insulation resistance tests.
BLDC Motor	If the electronic brushless inverter controller or permanent magnet winding is damaged.
Control PCB	If the control circuit board has a confirmed relay fault, burnt track, or micro-controller short.
Motor Capacitor	If the motor hums but cannot start rotation due to loss of microfarad capacitance.
Touch Panel	If capacitive touch sensors stop responding to touch inputs after cleaning the sensor glass.
Gesture Sensor	If infrared motion sensor board fails to detect hand waves to toggle speed or power.
Control Switch	If mechanical push switches or rocker switches are broken, loose, or burnt.
LED Light	If the chimney LED spotlight module or driver unit is burnt and no longer illuminates.
Auto-Clean Heating Element	If the heating pad around the blower casing shows zero resistance and fails to melt grease.
Oil Collector	If the plastic or stainless steel oil cup is cracked, warped, or has broken locking clips.
Baffle Filter	If stainless steel filter panels are severely bent, rusted, or have damaged handles.
Blower Fan	If the centrifugal blower fan wheel has cracked blades causing severe noise and vibration.
Duct Pipe	If the flexible aluminum exhaust duct pipe is punctured, torn, or crushed behind cabinets.

Faber Service by Appliance Type

Specific service and maintenance workflows for each type of Faber kitchen chimney.

Faber Auto Clean Chimney Service

Common Problem: Oil not draining into tray; heating pad remains cold during clean cycle.

Service Work: Multimeter testing of heating coil, relay trigger check, oil passage cleaning.

Parts Check: Heating pad, thermostat, relay switch, oil cup.

Faber Filterless Chimney Service

Common Problem: Oil mist deposits on motor casing, sudden drop in suction volume.

Service Work: Internal chamber degreasing, impeller cleaning, airflow backpressure check.

Parts Check: Impeller wheel, motor seal, oil channel, duct flap.

Faber Island Chimney Service

Common Problem: Ceiling mount vibration, smoke escaping open sides in island counter.

Service Work: Ceiling anchor inspection, high-speed motor balancing, dual touch panel test.

Parts Check: Ceiling brackets, double glass panels, heavy motor, PCB.

Faber Wall Mounted Chimney Service

Common Problem: Baffle filters choking with heavy Indian masala frying, light driver failure.

Service Work: Chemical filter wash, duct pipe leak seal, push button switch restoration.

Parts Check: Baffle filters, LED driver, push switch, wall clamp.

Faber BLDC Chimney Service

Common Problem: Inverter driver error, speed variation not functioning on voltage change.

Service Work: BLDC controller diagnostics, digital speed sensor check, low-voltage circuit test.

Parts Check: BLDC drive board, inverter motor, optical speed sensor.

Faber 6-Way Auto Clean Chimney Service

Common Problem: Partial cleaning cycle completion, corner grease buildup in duct chamber.

Service Work: Multi-point heater test, timer circuit check, deep manifold wash.

Parts Check: 6-way heating strips, timer relay, oil drain route.

Indicative Charges

Faber Parts Replacement & Service Charges

These are indicative service-platform ranges for service planning. Actual price depends on appliance model, part required, original/compatible part availability, fault, service location, and labour required.

Service / Work Category	Indicative Price Range	Work Details Included
Inspection / Visit	₹250 – ₹500	Technician doorstep visit, suction test, motor check, and fault diagnosis.
Minor Repair	₹300 – ₹800	Wiring connection fix, duct tape reseal, light repair, or switch cleaning.
Switch / Knob Replacement	₹250 – ₹800	Push button unit replacement, rocker switch, or speed regulator toggle fix.
Small Electrical Part	₹400 – ₹1,200	Capacitor change, LED spotlight module, transformer, or gesture sensor board.
Motor / Fan Related Work	₹800 – ₹2,500	Motor bearing lubrication, blower wheel replacement, or motor coil rewinding.
PCB Related Repair	₹800 – ₹2,500	Control PCB relay servicing, track soldering, or electronic display board repair.
Major Part Replacement	₹1,000 – ₹5,000+	Complete chimney motor replacement, BLDC inverter drive unit, or canopy glass.
Installation / Service	₹500 – ₹1,500+	Wall bracket mounting, chimney hanging, core-cutting alignment, or duct routing.

Important Pricing Disclaimer: Final charges are explained after inspection before starting the repair. We do not promise fixed prices over the phone. Replacement part costs vary by model compatibility and manufacturer availability.

Finding a Faber Chimney Service Near Me?

When your kitchen chimney suction slows down or noise increases, finding prompt doorstep support matters. Our trained technicians visit your home to inspect, clean filters, and tune your chimney for peak performance.

Looking for Faber Chimney Repair?

Whether your chimney motor will not start, the auto-clean heating pad fails, or touch buttons stop responding, we offer complete diagnosis. We test electrical parts first before suggesting replacement.

Need Faber Chimney Parts Replacement?

If an internal component like a capacitor, blower fan, LED light, or PCB board is confirmed faulty, we check part availability for your exact Faber model and provide a clear upfront estimate.

Why Us

Prompt technician visits at your home across selected cities in India.

5 Steps

Our Faber Chimney Repair Process

1

Call or WhatsApp

Reach our support team by phone call or WhatsApp message.

2

Share Model Details

Tell us your Faber chimney model, size (60/75/90 cm), and fault.

3

Technician Visit

A trained technician is scheduled to visit your doorstep.

4

Fault Check

The technician inspects the motor, blower, heating element, and ducting.

5

Repair / Service

Service or cleaning is performed once you approve the estimate.

Nainital Rd, opposite City Hospital, Heera Nagar, Haldwani, Uttarakhand 263139

Phone: 8882055269

Haldwani Chimney Service Call Service

Questions

Faber Chimney Service FAQs

Suction drops when baffle filters are saturated with grease, the motor blower is choked, or the duct pipe has bends. Regular cleaning and duct checking restore full suction.

Filters should be cleaned every 3 to 4 weeks at home. A professional deep cleaning of the motor and internal blower is recommended once every 6 to 12 months for heavy cooking.

Loud noise can happen when grease sticks unevenly to blower blades, motor bearings become dry, or the wall mount bracket gets loose. Our technician inspects and balances the motor.

If the auto-clean heating pad does not get warm, the heating element or control relay may have failed. The technician checks the circuit and restores the heating function.

Yes. If touch or wave gesture controls do not respond, the sensor panel, optical glass, or electronic PCB is checked, cleaned, or repaired as required.

Inspection visit charges generally range between ₹250 and ₹500 depending on location. The technician gives an exact estimate before beginning any repair work.

Yes. Doorstep chimney service is available across selected cities so you do not have to uninstall your chimney.

Simply call our service number or send a WhatsApp message with your city, address, and the chimney problem. We arrange a technician visit at a convenient time.

Manufacturer Reference Information

Official Faber India Information

This website is an independent service platform and is not the official Faber India website or an authorized Faber service center. If you require official manufacturer warranty support, please contact Faber India directly:

Official Website: https://faberindia.com/

Faber Customer Care: 1800-209-3484

Official WhatsApp: +91 7219219219

Customer Care Timing: 8:00 AM to 8:00 PM, all 7 days

Quick Support